Airo Shot Blast

Spares Parts of Flame Spray Gun There are some  spare  parts used in a  flame spray gun   and these are- Air Cap. Air Cap Body. Nozzle Nut. Nozzle. Siphon Plug. O-Ring. Siphon Plug Wire comes first in the siphon plug and then in the nozzle, it completely holds the wire. The siphon plug should be cleaned occasionally. Wipe out the grooves and clean out the holes with the proper size wires from the cleaning wire kit. Do not wash the o-rings with a cleaning solvent. Examine them for damage and replace them if required. Do not stretch new o-rings more than necessary. Lubricate all o-rings before reassembling the siphon plug. Nozzle I n the  flame spray gun , there is a nozzle after the siphon plug. Whenever a nozzle is put on the gun, the bore of the siphon plug should be wiped clean and put on the nozzle O-rings. The nozzle nut must be tight on the siphon plug. Firm tightening by hand is sufficient. Overtightening the nozzle nut ...

Gas flow meter The  gas flow meter  is a highly accurate and reliable instrument for regulating and measuring the flow of both oxygen and fuel gas in a manual powder and wire thermal  spray gun . It has precision needle valves which are actuated by adjustment knobs on the front panel that controls the flow of gas through the meter. Flow unit readout is provided in both Metric (NLPM) and U.S. Customary (SCFH) units. The separate flowmeter is provided for the regulation of oxygen and fuel gas (acetylene or LPG), which are isolated from each other. As an additional safety feature, each meter incorporates a check valve in the piping from the meter outlet to the combustion  spray gun , which protects against high back pressure that could result from gun backfire and prevents any possibility of mixing of the process gases with each other. These check valves can be replaced when necessary. Acetylene, hydrogen, propane, MAPP and natural gas can be safely used in th...

Boiler Tube Coating Boiler Tube Coating is a must for increase life of boiler tubes.  The  Thermal spray -on boiler tube coating technology to give high-temperature wear & corrosion protection coating on the boiler tubes. A broad type of coating materials such as mild steel or other metals or alloys is available. Therefore a proper coating can be utilized on the tubes to combat the specific queries without changing the tube material. Thermal spray coating is a general name for a combination of processes in which a wire/ powder is melted, either by fuel or electrical means, to its melting point, atomized by the usage of pressurized air & then moved onto the prepared component. The melted particles hit the prepared surface & fix instantly, create up layer upon layer to make a coating. Boiler Tube Coating is done by Two Processes these are following TWIN WIRE ARC SPRAY GUN The  twin wire arc spray gun  process uses metal in wi...

Metalizing Gun Price Metalizing gun  price depends on the type of metalizing gun . Price varies according to models.  The   metalizing spray gun   is known as   thermal spray coating , is widely used in preventing the corrosion of metals. Metal wire or powder is filled at a measured rate into a flame or arc spraying process and the atomized metal impinges upon the surface being coated and becomes bonded to it. The coating is capable to form protective layers and can also work as a sacrificial anode. That protects the underlying steel or iron resulting in minimal to no maintenance for years to come. Zinc and Aluminum Wire are the most commonly used. When sprayed on steel, the alloy produces a coating with the best anti-corrosion protection. Metalizing Wire Flame Spray Gun: The metalizing  wire flame spray gun  is a method that utilizes an oxy-fuel flame to melt wires and in some instances powders or ceramic rods. The molten substance (mater...

Metco Metalizing Gun Metco 12E Wire flame spray Gun  Metco 12E  ( Metco Metalizing Gun ) uses a single wire that is entered in a jet flame. The temperature is close to 10,100 K, melting the wire. The air stream from the jet atomizes the molten particles, falling them onto the substrate. A  Metco Metalizing Gun  system uses a combustible gas mixed with oxygen to create a flame outside of the spray gun of approximately 5400° F. This is the heat source to melt the metal to be sprayed. The material to be sprayed is in the form of a wire that falls into the center of the flame where it is melted. Metco 2AF The  Metco 2AF  ( Metco Metalizing Gun )   is an airflow meter designed to control the airflow to the WireJet Series of guns.  Air Trio is created for the Wire Jet series gun, it has a particle filter, water trap and air pressure regulator built within one unit. There is another quick disconnect for cooling air jets or other a...